How To Add Stabilizer To Pool Without Skimmer?

As someone who has spent countless hours maintaining their pool, I know that balancing water chemistry is crucial to enjoying crystal-clear water all season long. One of the key elements to maintaining the right chemical balance is adding a stabilizer to the pool.

Stabilizer helps prevent chlorine degradation from sunlight, ensuring your pool stays sanitized and safe for swimming. However, adding a stabilizer to your pool can be challenging if you don’t have a skimmer.

Typically, skimmers are used to distribute chemicals evenly throughout the pool. In this article, I will share some alternative methods that you can use to add a stabilizer to your pool without a skimmer. Therefore, without further ado, let’s dive straight in.

✍ Pro Tip: Before adding the stabilizer to the pool, dissolve it in a bucket of warm water, helping it dissolve evenly and preventing it from settling at the bottom of the pool and potentially staining the surface.

How To Add Stabilizer To Pool Without Skimmer?

The stabilizer is a chemical used to stabilize the Chlorine level of pool water. Following some steps, you can easily add a Stabilizer to the pool without Skimmer. They are given below:

Materials Needed:

• Stabilizer
• Bucket
• Warm water
• Pool test kit

1.    Take Safety Measures

Above all, take some safety measures by wearing gloves to ensure your hands are safe when handling Chemicals. Before doing anything, put on safety gloves, a mask, and goggles.

2.    Fill A Bucket With Warm Water

After that, take the large bucket that will be enough for the work and fill it with warm water. You can also use a plastic or Aluminium bucket for this process.

3.    Add Stabilizer

Now add the stabilizer to the bucket. You can also use Cyanuric acid or other Chlorine conditioner products according to your pool condition or the recommendation by the pool’s manufacturer.

4.    Add Mixture To The Pool Water

Gradually add the combination of warm water and stabilizer to your pool water. Stroll around the pool’s edge and attempt to disseminate the combination as equally as possible, covering all shapes of your pool.

5.    Run The Pool Pump

After adding the mixture to the pool water, run your pool pump for a few hours. This way, you can quickly stabilize your pool water.

☝ Pro Tip: Allow the pool water to circulate for at least 24 hours before testing the chemical levels again using a pool test kit.

To dissolve Pool Stabilizer, you must first clean your leave catcher. There is another leaf basket, so get them all cleaned out. Next, take the leaf basket and put the white sock or white material in it.

Pour The Stabilizer

After that, pour the pool stabilizer into it, which will dissolve slowly as the Pump draws water across the top. Don’t throw the stabilizer into the pool and mix it in a bucket because it takes forever to dissolve; that’s why you should use the cloth.

Put The Basket In The Pump

Now put the basket in the Pump and turn it on the Pump. The Pump has a plastic impeller on it, which is tight against this housing the whole way around, and if you put granules in there, the little ones will go through the screen.

Importance Of Using Sock And Cloth

And, don’t get bound in between the plastic and the impeller and grind a little bit, which can wear out your Pump, any slight tolerance that’s not tight like worn down a little. It will affect your water pressure, and you don’t want that, so that’s what the sock and cloth prevent.  

Feeling a little stuck in the process? Don’t sweat it! We’ve got your back. Check out this helpful video that breaks down the steps for dissolving a stabilizer in your pool.

How To Increase Stabilizer In Pool?

To Increase the Stabilizer in the pool, simply add the stabilizer. Remember, CYA (Cyanuric Acid) is an acid it can damage your filter and pool, especially if you have a vinyl liner.

Types Of Equipment Used To Increase Stabilizer

However, always read the manufacturer’s instructions before using it, but here’s how we recommend adding it to your pool. You will need Cyanuric acid, a five-gallon bucket, acid-resistant gloves, and warm water.

Fill The Bucket

First, fill the bucket halfway with warm water, put on your gloves and goggles, and add cyanuric acid to the bucket. Check the product instructions for your pool size.

General Rule To Add Cyanuric Acid

However, as a general rule for a 10,000-gallon pool, you must add 13 ounces of Cyanuric acid to increase your CYA by 10 parts per million. Pour the contents of the buckets directly into your skimmer and then run your Pump for at least a few hours to stir in the solution to your pool.

Related Post: How to Increase Calcium Hardness in Pool

FAQs: How To Add Stabilizer To Pool Without Skimmer?

Conclusion

Adding a stabilizer to a pool without a skimmer is essential to reduce the chemicals needed to maintain the pool and increase its longevity. To add a stabilizer to a pool without a skimmer, follow the steps outlined in this article to make this tiresome task a piece of cake.

Notably, test the pool’s pH levels regularly to ensure the stabilizer is working properly. With these steps, you can easily add a stabilizer to your pool without a skimmer and enjoy a crystal-clear pool for years.

Keep your pool in tip-top condition with our expert guides at thepoolmania.com!